# Beetlejuice Pinball Setup Tutorial

**Source:** Spooky Pinball  
**Type:** video  
**Published:** 2026-02-23  
**Duration:** 14m 35s  
**Beat:** Pinball

**URL:** https://www.youtube.com/watch?v=zvKUjTrK0_0

---

## Analysis

Spooky Pinball releases a comprehensive setup tutorial for the Beetlejuice pinball machine, covering single-person assembly from unboxing through initial playfield setup. The video details critical procedures including topper removal, leg installation with precise pitch calibration (6.7-6.9°), packing material removal, and safety precautions to prevent damage during assembly.

### Key Claims

- [HIGH] Beetlejuice can be set up by one person, though two or three helpers is better — _Opening statement of tutorial video_
- [HIGH] Ideal pitch range for Beetlejuice is 6.7 to 6.9 degrees, with 6.8 as the target — _Detailed technical specification during back leg installation section_
- [HIGH] Front leg leveler bolts should be threaded all the way down to ensure both sides match — _Front leg installation procedure_
- [HIGH] Back leg leveler bolts should stick through approximately 7/8 of an inch to achieve proper 6.8° pitch — _Back leg installation with ruler demonstration_
- [HIGH] Six balls are included in the leg box — _Leg box contents inventory section_
- [HIGH] Packing material must be completely removed before powering on the machine to avoid severe damage — _Safety warning during playfield preparation_
- [HIGH] Users should check the Spooky Pinball website after initial power-on to verify they have the latest code version — _Post-power-on instructions_
- [HIGH] Foam from the coin box should be placed on the apron when putting the playfield in service position to prevent damage — _Final maintenance tip section_

### Notable Quotes

> "It's better if you have two or three some friends to help you out, but it actually only just takes one person."
> — **Spooky Pinball setup technician**, 0:00-0:15
> _Sets expectations for assembly difficulty and flexibility_

> "Warning, it is kind of heavy, so just be ready for that."
> — **Spooky Pinball setup technician**, ~1:30
> _Safety warning about topper box weight_

> "throw the tilt bob away. Who uses them?"
> — **Spooky Pinball setup technician**, ~5:30
> _Dismissive commentary on tilt bob accessory, suggests it's not needed_

> "The pitch that we're trying to get to with Beetlejuice is in between the range of 6.7 to 6.9. Uh, in this video, we're going to go for 6.8."
> — **Spooky Pinball setup technician**, ~7:45
> _Critical technical specification for optimal gameplay_

> "It's extremely important that you get the game set to the right pitch and that the game is level."
> — **Spooky Pinball setup technician**, ~7:30
> _Emphasizes critical importance of pitch and leveling for Beetlejuice specifically_

> "You don't want to set it down on concrete. You run the risk of it shattering into literally a million pieces."
> — **Spooky Pinball setup technician**, ~15:30
> _Safety warning about glass playfield protection_

> "Please take out all of the packing material before turning the game on. If you don't take out this packing material before you turn your game on, you could do some severe damage to it."
> — **Spooky Pinball setup technician**, ~14:45
> _Critical safety instruction to prevent machinery damage_

> "Always check the Spooky Pinball website to make sure you're on the latest version of Code."
> — **Spooky Pinball setup technician**, ~22:00
> _Post-setup maintenance recommendation for code updates_

### Entities

| Name | Type | Context |
|------|------|---------|
| Beetlejuice | game | Limited-edition pinball machine by Spooky Pinball released November 2025, subject of comprehensive setup tutorial |
| Spooky Pinball | company | Manufacturer producing Beetlejuice; provides official setup tutorial and customer support services |
| Dante | game_feature | Character/toy element on Beetlejuice playfield with horns requiring protective tape removal during setup |
| sandworm | game_feature | Mechanical toy feature on Beetlejuice playfield with motorized mechanism requiring careful packing material removal |

### Topics

- **Primary:** Machine setup and assembly procedures, Pitch calibration and leveling specifications, Packing material removal and safety precautions, Leg installation and hardware assembly
- **Secondary:** Post-setup maintenance and code verification, Service position and playfield protection

### Sentiment

**Positive** (0.85) — Instructional tone is professional, helpful, and encouraging. Presenter demonstrates clear competence and concern for customer success. Dismissive comment about tilt bob ('Who uses them?') adds minor levity but overall sentiment is supportive and educational.

### Signals

- **[community_signal]** Spooky Pinball providing comprehensive official setup video and offering direct technical support (email and phone) demonstrates customer-focused service approach (confidence: high) — Video tutorial provided at no cost; service contact information given (servicespookypinball.com, 815-541-4940); offer to walk customers through questions
- **[product_strategy]** Detailed specification of 6.7-6.9° pitch range with 6.8° target and specific back-leg leveler measurement (7/8 inch) indicates deliberate pitch calibration is critical to Beetlejuice gameplay (confidence: high) — Multiple references to pitch/level importance; specific measurements provided; presenter checks pitch after setup completion
- **[product_concern]** Emphasis on careful packing material removal and multiple safety warnings suggests potential for customer damage during assembly if not followed precisely (confidence: medium) — Repeated warnings about not damaging cabinet, decals, glass, and mechanical features; emphasis on following specific pitch/level procedures

---

## Transcript

Welcome everybody. Today I'm going to be showing you how to set up your Beetlejuice pinball machine with just one person. It's better if you have two or three some friends to help you out, but it actually only just takes one person. And I'm going to show you how to set it up for the ideal settings for your game play as well as other safety precautions to take while setting it up so you don't damage anything. As per usual, we are going to start on the truck this side only portion of [music] the game as that is the bottom of the cabinet. All right, so after you have your game in place, it is time to get that topper [music] off there. Uh, sounds like pretty much most every single one of you out there got a topper. So, yeah, this will obviously be step one. You're going to cut the two straps with a pair of wire cutters. Get those straps pulled out and out of your way. And then we're going to get the topper off the top of the game. There are two hard protective corners in the front and back side of the topper. You're going to want to go ahead and grab those and remove them from it. Uh, if you don't do that and you go to pick up the topper, those will probably fall off and like hit you in the head or something. So, don't do that. Uh, take those off and then go ahead pick up the topper box. Warning, it is kind of heavy, so just be ready for that. So, now you're good to go ahead and cut off these two straps that are holding the box over top of the game. Go ahead, cut those. Pull them out of your way. I recommend holding on to the straps more than I did so that the cables don't kind of go flying everywhere. Uh, and then from there, you are okay to lift this box off the game. So, I recommend uh squatting down. You're going to get your hand up underneath that cardboard and lift straight up. You're going to lift it all the way up over the top of the game and get out of your way. If you don't have the head clearance to do this, just cut down the side of the box with a knife and peel it off. The next thing you'll want to grab after you've got that box off is your leg box, which is tucked away back behind these straps towards the back side of the game. So, pull that out of there and go ahead and set it somewhere like a table where you can work on the box later. All right. So, at this point, you can go ahead and cut the last two straps holding the game down to [music] the pallet. Uh, go ahead, cut those. Pull them through just like you did the other ones. Get rid of that. And then just a friendly reminder here to be very careful about not cutting the shrink wrap that holds the head up to the game. We're not going to cut any shrink wrap material yet, but what we are going to remove is this cardboard material on the top of the [music] game. There'll be two on the top by the coin door and one back by the topper. So, we're going to go ahead and get those removed. Uh, you honestly don't even really need to cut it. You could probably just rip it off or pull it off, but I'm just kind of gently going through and cutting the small pieces of tape, holding those down here with a knife and uh [music] getting those out of the way so that we can get access to the leg bolts and open up that leg box, get the legs attached, and start getting this thing uh more on four legs. So, I'm going to remove this last piece of cardboard that is back behind the topper here. And then I'm going to do something to the pallet. I'm going to cut these corners [music] where it's taped up on this pallet to free this box open so that it's a lot easier to set the game down later once we have all the legs on. This will make more sense later when John Youssi it. But now it's time to go ahead and open up the leg box [music] and uh let's check out all the contents that we have in there and start getting everything ready to go onto the game itself. So once you're into the leg box, there's a very helpful note in here showing you all of the details about [music] how to properly set up your game in case you don't feel like listening to me in this video. And then we're just going through and grabbing all the items out of the leg box. Starting with those, uh, leg leveler bolts there, and then the felt protectors. All of this stuff is pretty important. Uh, you know, some of this is replacement parts. Uh, throw the tilt bob away. Who uses them? Uh, go ahead, set aside things like your power cable, your balls, uh, the felt protectors, and what I always do, uh, make sure, oh, by the way, make sure you have six balls in that bag. You got your head bolts. Uh, go ahead, grab your keys. And what I always do is I just walk right over and I put those right into the coin door so I don't lose them. misplace them, dog gets a hold of it, whatever it could be, just get that thing right in the coin door so you have it ready later for when we need to get into there. [music] And then uh there's also some replacement parts here. So if you have a servo that ever goes down, you got a spare servo on hand, as well as uh any stickers. Uh if you chew up your target decal stickers, you know, we got some [music] extra parts in there for you for that, too. So with Beetlejuice Pinball, it's extremely important that you get the game set to the right pitch [music] and that the game is level. Uh, what I always do in all of our spooky [music] games is the front legs. I always thread in this leg leveler all the way down. I just I thread it in all the way down so that I know both sides match perfectly. Uh, if the floor is uneven or something and you need to adjust them later, that's fine. But I I always just start with these front ones all the way down. You know, the pitch that we're trying to get to with Beetlejuice is in between the range of 6.7 [music] to 6.9. Uh, in this video, we're going to go for 6.8. Anywhere in that range is really good. But yeah, this game is extremely important to make sure you have it pitched and leveled. So I thread that light bolt all the way in. And I'm going to do that for both of them. Then we can install it on the game. So before you go and put your legs on, obviously you want to get some of this packing material out of the way. So just make sure you fold back any material that could get caught underneath your [music] legs. Fold that back off of the game. And then you are good to remove the leg bolts. I'm using a 5/8 socket [music] here. Uh I have it attached to a drill. definitely the quickest way to go about doing it, but I mean a wrench works perfectly fine. Uh so just whatever works for you, whatever you have available, but go ahead remove all four leg bolts. Uh keep them somewhere obviously where you're not going to lose them. Uh don't set it on top of the game. You don't want to damage your powder coat or the decal or anything like that. A quick tip for adding the felt protectors to your legs is it makes it a lot easier if you fold them in half before you go and put it in there. If it's they're they're very firm and flat at the start. So, if you fold it in half, it makes it a lot easier to do this part of the process. But go ahead, put your leg bolts through. Make sure the felt protector is over top of those. And you are good to walk over and you can start to place the leg in there. So, you put the leg bolts in there. You're going to get them hand threaded first. Uh, so get them nice and uh threaded. Make sure it's not crossthreaded. Everything should be spinning very nicely in there. And then once you have it kind of most of the way fingertight, that's when I go ahead and I grab my drill and I get the leg the rest of the way tight. And you want to have this very tight. You don't want there to be any sort of wiggle room or wibbly wobbliness [music] to it in any way as that could potentially damage your cabinet as well as affect gameplay. So, make sure you have that leg really tight. Give it a good good shake. Then, just go ahead and repeat this process on the other side. Again, making sure that leg is really firm and locked in there. And then you're about ready to go ahead and tip this bad boy over. I'm just walking the game back a little bit right here so that it doesn't tip off the edge of the pallet. And then I go ahead, I grab it by its legs, I pull it down. I'm making sure the back is on the pallet still. Once it's set on its legs, we are good to go ahead and start getting ready to put the back legs on. So, for this part of the process, it is definitely best to have a person [music] to help you out. But if you're physically capable, you can go ahead and get in here and just pick up the back side of the game. Just be careful not to slip or trip. And then have a stool on hand or anything sturdy enough that you can slide under the game easily that can support the game's weight and it will safely rest on top of it, balance well and won't tip over. After the game is set up on whatever you choose to put underneath it, you're good to go ahead and remove the back leg bolts. And then we're going to kind of follow the same process that we did with those front legs, but we're going to set the leg levelers at a different height so that we can get the appropriate pitch for the game. So, we're good to start threading in the leg leveler bolts. Now, we're going to try to get the desired [music] pitch of about 6.8°. Again, between 6.7 to 6.9 is the sweet spot. To get that desired pitch of about 6.8, we found that a 7/8 of an inch sticking through the leg leveler bolt here is what you're going to be looking for. And I'll show you that on a ruler right here. So, just about 7/8 of an inch is right about where that sweet spot is. You could, of course, thread this back uh either direction a little bit if you want to try to get more of that 6.7 6.9. Uh but yeah, right around there. 78 of an inch seems to be the sweet spot. And then you're good to install these in the back the same exact way that you did the ones in the front. Throw your leg bolts uh fold your foam in half and then thread your leg bolts through the leg. Get the foam slapped on there and get it secured nice and snug to the back side of your game. So, now that we got all four legs secured, we're going to go ahead and kick the stool out of the way. Just like that. And you can go ahead and set the game down now. So, the next goal is going to be to get [music] all this packing material off there. I would recommend using a pair of scissors or a utility knife. Just be extremely careful that no matter what you use, you don't cut into or damage the armor or the decal of the game. So, I'm using a pair of scissors in this video. It's not what I would normally use, but I wanted to try to show it. So, we're just using a pair of scissors, really gently and carefully going up along the side of this material, pulling it tight so it's away from the cabinet and cutting [music] it so that it's all released off of there. And then we're just going to pull all of that out of the way. And you're then safe to go ahead and raise the head up uh into the gameplay position. So, an important note here is to make sure that when you raise this head up that you feed the tube into the cavity of the cabinet here. Uh, if you don't feed the tube through there, it could get bunched up and pinched in between the cabinet and the head of the game, which uh, you don't want to be doing that. You don't want to cause any sort of stress or damage to your wires. So, here you'll be met with our world famous, please take out all of the packing material before turning the game on. Uh, if you don't take out this packing material before you turn your game on, you could do some severe damage to it. So, please don't turn the game on yet. Let's take out this packing material first. And to start doing that, we're going to have to take off our [music] glass first. So, we're going to go ahead remove the pre-space tape with our foam padded protection pieces here [music] on either side of the game. So, you'll have two on the left side, two on the right side. We're going to get both of those ripped off. And then we are going to go to the coin door. We're going to open that up. And there's going to be these [music] latches inside there that will release your lock down bar. This is what those latches look like. Uh it'll have some tension on it cuz it's holding that lock down bar on. And that's on the right and left side just inside your coin door. So when you open your coin door, kind of reach in just like this, and then that's where those latches [music] are. So you reach in there, unlatch those, and then when it's free, you can pull out the lock down bar, set that aside somewhere nice and safe where it won't get scratched or damaged. Make sure you close your coin door, and then you are good to go ahead and remove the glass from the game. Uh do make sure you close the coin door, otherwise you'll probably bump it with the glass. Make sure to not set that glass down on concrete. Me showing here. Yeah, you don't want to set it down on concrete. You run the risk of it shattering into [music] literally a million pieces. So, find somewhere padded and safe to set that down. All right. Now, it's time to start removing all of the packing material. We're going to start with the cartridge there. Just a [music] little piece of tape around that. And there's actually not a ton of packing material to remove, so it won't take you [music] any time at all. So, we're going to go ahead go over remove that Dante tape that is up around his horns protecting those from the glass. We're going to get rid of that. And we got the sandworm and beetleju left here. So, we're going to get this tape off the gargoyle in front of Beetlejuice. Uh it's kind of wrapped around his head and his wings and whatnot. So, we're going to get that removed. And then with Beetlejuice, uh we want to be a little bit specific here. So, that foam is packed in in front of him. What I recommend is that you grab a hold of Beetlejuice, get your finger in there, and then you just pull the Beetlejuice mech up, and that will free the foam to come out. You don't want to just rip and pull on this foam. Uh, it would just kind of shred it and make a huge mess. So, just [music] pull him up. And then you have this lightly packed foam around the sandworm. Go ahead, get rid of that. Uh, take get rid of the the piece underneath him and then the piece around his fin. At this point, we're almost there. We're getting so close to playing the game. So, I got my six balls. [music] I'm just wiping those down real quick, making sure there's no grease or any sort of debris [music] or anything on them before throwing them into your brand new shiny playfield here. So, I cleaned those off real quick. Go ahead, drop those into the game. And then before we put the glass back on, I'm just going to check that I am happy with my pitch. And as I set that down, John Youssi I'm locked in right at 6.8, right where I wanted it. And then I'm also checking my level side to side as well. Again, pitch and level in Beetlejuice very important for the layout to function properly. So, please double check these. My level is pretty gosh darn good. Could be a little better, but it's pretty good. Uh, so at this point, I'm going ahead and I am sliding back in the glass. We're going to get the glass slid in. We're going to get our lock down bar back on. And then all that's left to do is, uh, secure that lock down bar and get this game plugged in. And you're pretty much ready to go ahead and start playing your Beetlejuice pinball machine. So, after we get the game plugged in here, we're going to go ahead reach under the bottom right side of the cabinet, turn that [music] power switch on, and then we're going to be met with a loading screen. This loading screen is going to tell you what version of code you're on. Always check the Spooky Pinball website to make sure you're on the latest version of Code. And then, yeah, your game is up. Get your balls in, glasses ready to go. You're you're ready to start playing your game. As you can see here, uh the only other last thing that [music] would be left to do, a little something, you can peel the plastic off your topper that came with the game. But chances are you have the aftermarket [music] topper. So stay tuned to watch the video for how to install that. Speaking of toppers, something [music] extremely important you want to do to ensure that you never damage either the aftermarket topper or the one that comes with the game [music] is that you add the piece of foam from the coin box onto the apron if you're ever to put your game up in the service position as shown here. So to get that piece of foam, if you ever need to put this playfield up, you're just going to go inside the coin door. Here's going to be a coin box. That coin box is held [music] in with a cotter pin. Go ahead, just pull that cotter pin off back there. You're going to lift the box straight up and then just rotate it and pull it out. And then inside this coin box [music] is where you're going to find the piece of foam that you can put on the apron. It'll have a little slit in it so that it slides [music] right over top. You go ahead and push that on there nice and firm so that it doesn't pop off or fall off on your way up to the top of the game. And then from there, you're okay to set the playfield in the service position up against the topper without risking damaging anything. Of course, if you have any questions at all about this process, please do not hesitate to reach out to our service department. You can email them at servicespookpypinball.com or just give us a phone call at 815-541-4940. We [music] are more than happy to walk you through anything that you may have for questions or [music] in this process of setting up your

_(Acquisition: youtube_auto_sub, Enrichment: v3)_

---

*Exported from Journalist Tool on 2026-04-13 | Item ID: 2848ef75-bdbd-4683-ace4-5bf9844d8de8*