# Hook Pinball Repair Series: Episode 2

**Source:** Cary Hardy  
**Type:** video  
**Published:** 2019-08-14  
**Duration:** 11m 45s  
**Beat:** Pinball

**URL:** https://www.youtube.com/watch?v=fympLMXUll8

---

## Analysis

Cary Hardy demonstrates intermediate-level Hook pinball machine repair and maintenance in episode 2 of his repair series. The video covers diagnostics (reseating connections and ROMs, switch testing), troubleshooting (identifying missing fuses, correcting poor solder joints, replacing a faulty trough switch), and playfield teardown methodology. Hardy emphasizes organized documentation during disassembly and plans future content on playfield clear coating.

### Key Claims

- [HIGH] Reseating connections and ROM chips can restore display functionality on pinball machines — _Hardy demonstrates reseat procedure and confirms display works immediately after reseating connections and ROM_
- [HIGH] Missing F5 fuse (Slow Blow 5 amp) prevents solenoid function in this pinball machine — _Hardy explicitly states: 'I did not have my F5 fuse, which is very important to your solenoids actually all function. So once I installed a Slow Blow 5 amp, then all my solenoids worked.'_
- [HIGH] Poor soldering quality on switch connections can cause intermittent switch failures — _Hardy identifies corroded trough switch with poor soldering and performs reflow to fix connection issue_
- [MEDIUM] Complete topside playfield teardown can be accomplished in approximately one hour — _Hardy times himself and reports one-hour teardown time, though notes some components require underside access_
- [HIGH] Organizing playfield parts by section in labeled Ziploc bags facilitates reassembly — _Hardy demonstrates and endorses this organization method as helpful for reassembly: 'Every section that I take apart, I keep everything in that section in its own bag and I label it accordingly. This is very helpful for whenever you're putting a playfield back together again.'_

### Notable Quotes

> "I basically want to consider it a shop job but taking up an extra 10 notches...I'm not planning on doing any kind of cabinet restoration, but I am mainly looking out for the playfield."
> — **Cary Hardy**, 0:30-1:00
> _Defines the scope and purpose of his repair work on the Hook machine_

> "I did not have my F5 fuse, which is very important to make your solenoids actually all function. So once I installed a Slow Blow 5 amp, then all my solenoids worked."
> — **Cary Hardy**, 7:20-7:35
> _Educational diagnostic tip about critical component verification in pinball repair_

> "I don't like the soldering on this. This looks kind of crap. I'm going to do a reflow on this."
> — **Cary Hardy**, 6:00-6:10
> _Demonstrates quality inspection and remediation during diagnostics phase_

> "This is the way I tend to organize my playfield teardowns. Every section that I take apart, I keep everything in that section in its own bag and I label it accordingly."
> — **Cary Hardy**, 10:50-11:05
> _Best practice methodology for complex reassembly work_

> "It took me one hour to completely tear apart the top of this playfield."
> — **Cary Hardy**, 10:00-10:10
> _Establishes realistic timeframe expectation for playfield disassembly_

### Entities

| Name | Type | Context |
|------|------|---------|
| Cary Hardy | person | Content creator specializing in pinball repair and restoration with educational video series focused on hands-on demonstrations |
| Hook | game | Pinball machine being repaired and restored in Hardy's video series; currently undergoing diagnostics and playfield teardown |

### Topics

- **Primary:** Pinball machine diagnostics and troubleshooting, Component-level repair (fuses, switches, solder joints), Playfield disassembly and organization methodology, Educational content for pinball enthusiasts
- **Secondary:** Future playfield clear coating techniques

### Sentiment

**Positive** (0.85) — Hardy expresses satisfaction with successful repairs ('Yay on that,' 'Thumbs up on that'), enthusiasm for the project, and optimism about future work. Tone is educational and encouraging toward viewers.

### Signals

- **[community_signal]** Hardy creating educational video content focused on teaching pinball repair techniques to his audience (confidence: high) — Explicit statements about showing educational processes: 'but I'm going to be doing this for educational purposes to you guys'; consistent teaching narrative throughout video
- **[technology_signal]** Video demonstrates systematic diagnostic methodology (reseating, fuse verification, switch testing, solder quality inspection) typical of experienced technician (confidence: high) — Hardy methodically tests each system component and identifies root causes (missing fuse, poor solder joints, faulty switch) with clear explanations

---

## Transcript

 What's going on guys and welcome back to my channel where I talk and do everything pinball. So if that sounds interesting to you then hit that subscribe button down below. I'm back with another episode with the hook. I don't want to call it a restoration. I basically want to consider it a shop job but taking up an extra 10 notches. However you want to take that. Meaning that I'm not planning on doing any kind of cabinet restoration. but I am mainly looking out for the playfield. So this is something I want to show you down the road on things that you can do, and technically I didn't even have to do with this machine, but I'm going to be doing this for educational purposes to you guys, and that consists of how to clear coat your playfield. I know there are plenty of you out there that would love to know how to do that, and there are many ways to go about doing it, but I'm going to show you how I'm going to do it for this game. But that's going to be down the road. So let's go back to showing you what I've done with this hook machine so far. So one thing I want to try when I want to get this display working or see if it works is I want to basically reseat all my connections and ROMs. So by simply, usually just removing this connector, even giving it just a little bit of wiggle out, reconnecting it back in. Same thing on my ribbon cables. On the board, make sure you don't cross slot anything or miss any pins. Don't want to bend any pins. Connections are all reseated. Take this ROM out. This is where you gotta be real careful about it and put it back in. Alright. So by reseating all the connections and reseating the ROM chip on the video, let's see what we get. bye Hark Hark Hark Bam Man that display looks pretty good actually Looks real good So now Now let's go into settings. Tickler pinball missing. Single right target. For what switches I can reach they all seem to work let's try down the trough so shooter lane works trough one works really so trough two doesn't work over trough three that one that seems like it might just be a loose and dirty connection right there so I'm going to clean that up I'm going to clamp this down a little bit to get that tighter connection right there then we'll try and see if that fixes it just got some 500 and sandpaper right here to get off any of that corrosion that's on there then I'm going to time this down a little bit Get that on there nice and snug So now will it work No that not the only problem. I don't like the soldering on this. This looks kind of crap. I'm going to do a reflow on this. This looks kind of crappy. See if that fixes the issue. Alright, so let's talk about things that I fixed. I've got essentially, yeah, I didn't record everything, guys. I'm sorry. But let's talk about what it is I did to get this machine fully working. And one thing for sure, not only do you want to check your fuses, but you want to make sure that you have a fuse in every holder. I did not have my F5 fuse, which is very important to make your solenoids actually all function. So once I installed a Slow Blow 5 amp, then all my solenoids worked. So yay on that. As far as anything in the backbox, that was the only thing that needed to be done. When it comes to my switch issues, I replaced this switch, trough number two, and refloated. So, we got all different switch right there. So that fixes my trough issue. Thumbs up on that. The other problem, I could not find this damn target, but this target right here, I guess it got hit really hard. was pushed up like that activating so that fixed that issue so as long as I guess it didn't get hit too hard like it did I guess at one point then we should be okay on that and I want to say that was it that fixed everything everything is good to go now so everything functions I've been playing this game just to make sure everything functions. Now I guess is the time to disassemble and start making this thing look sexy. So let's talk about the tools that I will be using for a playfield breakdown. This is a multi screwdriver that has different sizes and can do a lot of work with just one tool. Clippers basically to cut any type of zip ties that may be underneath the plate. Pliers are pretty obvious but that usually is to loosen up any kinds of nut that's underneath the plastic in order for me to get it off. Then I have that hook tool for just in case I have like an e-clamp or something like that on one of the diverters or something like that that usually comes in handy. Then I have my mini screwdriver set which comes in handy in a lot of cases for the little bitty screws. a flashlight for those just purposes then I have my complete nut driver set and of course my soldering iron Playfield is out of the cabinet and we using an uncommon sort of playfield lifter. This is something that I've used before in the past for some of you that have followed my work is that I'll leave it on the black black knife complete hardtop we utilize beer cans. Here's a time lapse of me taking this playfield apart. Now, at the beginning of this, I started the timer, but I didn't realize that it wasn't going on the television screen. So I do go in there and make sure I refresh the screen to show you that, yes, I have been timing myself since I first began. And I do a complete topside teardown on this playfield within a certain time frame. Thank you. One hour it took me to completely tear apart the top of this plate fill. Yes, there are a couple of things that I could remove also and I will be removing everything. So it's just a matter of getting all the main stuff off of the plate fill. Everything else is going to require me to go underneath the plate fill to get it. Here is everything in the Ziploc bags. This is the way I tend to organize my playfield teardowns. Every section that I take apart, I keep everything in that section in its own bag and I label it accordingly. This is very helpful for whenever you're putting a playfield back together again. And that's where we're going to end this video guys. That is showing you essentially the complete teardown hook and where we're going with this next is something that I'm pretty sure you're going to enjoy. So that's going to wrap it up guys. If you liked what you saw or you even learned something, then give me that thumbs up to to let me know. And if you haven't already, then hit that subscribe button down below. That way you can be notified of whenever I upload something for your viewing pleasure. Until next time, peace out.

_(Acquisition: youtube_groq_whisper, Enrichment: v3)_

---

*Exported from Journalist Tool on 2026-04-13 | Item ID: ba22a0c3-691c-48a4-9f7d-3411550df5ba*